Industrial Wi-Fi and Mobile Terminal Networks
In warehouse and production areas, we test handheld terminals, forklift displays and mobile equipment along the routes where they are used. We measure coverage, handover between access points and whether the application session is affected separately. If camera coverage of warehouse entrances and shipping areas is also part of the project, warehouse and shipping camera systems can be planned during the same site survey.
On-site measurementCoverage and capacityRoamingWarehouse Wi-Fi
What problem does this service solve?
Handheld terminals dropping out in the aisles
While the operator is scanning, the application session may drop as the terminal moves from one access point to another. The transaction is repeated or the record is left incomplete.
Coverage that changes as shelves fill and empty
A measurement taken in an empty warehouse becomes invalid when the shelves fill up. Products on the shelves can weaken the signal.
Mounting height and antenna selection
The access point’s mounting height, antenna type and angle affect coverage within an aisle. Metal shelving, changing stock, the client driver and how the application reacts to a lost connection are also checked separately.
Shared passwords
All terminals connect with a single password; a departing employee’s access is not closed unless the password is changed.
What we cover, and within what limits
In an industrial wireless network, coverage alone is not enough; capacity, roaming behaviour, interference and security are handled together. Metal surfaces, changing shelf occupancy, electromagnetic noise from machines and constantly moving clients require different measurements from an office. The input to the design is the client device: the bands and roaming features (e.g. 802.11k/v/r) supported by the handheld terminal and vehicle-mounted computer must be known from the start. The network is built around what the terminal supports. Carrying control or safety traffic wirelessly requires a separate design, manufacturer support and risk assessment; we do not recommend it as a default solution.
Technical scope
Requirements and client analysis
Which terminals and applications are used, which routes operators walk, how many devices are connected at the same time and how sensitive the application is to latency.
On-site measurement
The current state is measured; where needed, placement is verified on site with a temporary access point (AP-on-a-stick). Spectrum and interference are also observed.
Coverage and capacity design
Access point location, mounting height, antenna type, channel and power plan. Designed to work whether the shelves are empty or full.
Roaming and security
SSID structure, 802.1X or suitable authentication, device groups and VLAN mapping; roaming parameters suited to the terminal.
Installation coordination
Mounting, cabling and PoE requirements; enclosures and protection for dusty, humid or impact-prone locations.
Verification measurement
Re-measurement along the same route after installation, and a walking roaming test with a real terminal.
Design inputs for the wireless network
Coverage
Target signal and signal-to-noise ratio are set according to the client’s receiver sensitivity. Where possible, we carry out the acceptance test with the terminal model used on site.
Capacity
The number of simultaneous devices in the same area and the application’s bandwidth needs determine the number of access points.
Roaming
Handover time is affected by the client’s access point switching behaviour and authentication time. Roaming settings alone do not guarantee that the application session will not drop; session behaviour is tested separately.
Security
Per-person or per-device authentication, a separate VLAN and access only to the servers needed.
Prerequisites: what we need to get started
We list missing information and access together in the first meeting and complete them during the survey.
- Floor plan or warehouse layout (with shelf heights)
- Terminal models and applications in use
- Existing wireless infrastructure and management access
- Site access for measurement and safe access to high mounting points
- Information on IT’s authentication infrastructure
Deliverables
Requirements and client analysis
Pre-survey report and heat maps
Access point placement and mounting plan
Channel, power, SSID and security configuration document
Post-installation verification measurement
Roaming test results
Representative scenario: handheld terminal dropouts in a high-bay warehouse
In a high-bay warehouse, handheld terminals lose their connection in certain aisles. Measurements are taken along the route with the terminal used on site. In this scenario, the measurement shows that the signal drops within the aisles because of near-ceiling mounting and full shelves. The access point locations, antenna types and channel plan are renewed; roaming settings are aligned with the terminal manufacturer’s recommendations.
This is a representative project flow; it is not a completed customer reference.
Service summary
Industrial Ethernet and Factory Networks
We map switches, cables and connected devices from machine cabinets to the plant backbone.
Enterprise wireless network installation ↗
Scope limit
We do not offer carrying control and safety traffic wirelessly as a default solution. Office and campus wireless networks are covered by network.eretek.com. Work at height is carried out with equipment and permits that comply with occupational safety rules.
How do we proceed?
No step that affects production is carried out until the maintenance window, configuration backup and rollback plan are written down.
Analysis
Terminal, application and route requirements are identified.
Measurement
The current state and interference are measured.
Design
The placement, channel, security and roaming plan is written.
Implementation
Installation and configuration are coordinated.
Verification
Measured with a real terminal; acceptance is carried out.
Questions about Industrial Wireless and Mobile Terminals
Are office access points enough for a warehouse?
Sometimes. The deciding factors are the environment, mounting height, antenna options and client devices. The decision is based on on-site measurements.
Can we carry PLC communication wirelessly?
Some manufacturers offer dedicated solutions for this; however, latency, interruption and security risks require detailed design and risk assessment. Our default recommendation is to keep control traffic wired.
Is it enough to measure in an empty warehouse?
No. Shelf occupancy changes signal propagation significantly. Where possible, measurements are taken during a full period; otherwise, occupancy scenarios are taken into account in the design.
How are handheld terminals secured?
Instead of a shared password, we recommend device- or user-based authentication, a separate network segment for terminals and access only to the necessary application servers.
Work that can be planned together
Industrial Ethernet and Factory Networks
We map switches, cables and connected devices from machine cabinets to the plant backbone.
OT Cyber Security and Segmentation
We inventory the cells, engineering workstations and external maintenance connections in the production network.
Industrial Network Monitoring and Fault Analysis
For intermittent communication dropouts, we compare PLC and HMI logs, switch counters and downtime records on a single timeline.
Knowledge Center
Technical guides for this service
Industrial Ethernet
Let's plan a technical survey for industrial wireless networks and mobile terminals
Briefly describe your warehouse layout, the terminals you use and where they drop out; we will respond with a written proposal covering scope, assumptions and deliverables.